98-0940 on the Dyno

Integra Type-R Discussion - Discuss general ITR information, technical information (including requests for technical/mechanical help/assistance), modifications, tuning, etc.
Locked
Trey
Site Admin
Posts: 1004
Joined: September 10th, 2002, 11:43 pm
Location: TN
Contact:

98-0940 on the Dyno

Post by Trey »

My story to date.

Bought 98 R 0940 in may after selling 2000 R #891.

Dyno'd in May stock and made 159.9/110 whp
Dyno'd same day with an AEM and made 162.1/112.3 whp

Dyno'd Oct 20 with AEM, JDM 4-1/Carsound cat, 00/01 ITR intake cam, Stock Exhaust, Hondata Intake Manifold gasket, Stock ECU, Toda Cam gears set to Zero and made 178.1/125.3 whp

Dyno'd with my Power FC with a base map and made 179.5/126.9 whp. Did not go through the proper steps to tune so will have to report back.
pUrExTc
ITRCA Member
Posts: 294
Joined: October 7th, 2002, 5:04 pm
Location: Cerritos, CA
Contact:

Post by pUrExTc »

Wow! That's great! Just remember to turn off your A/C...I forgot to do that once...(it's an honest mistake!)
'98 Acura Integra Type-R
'03 Honda CBR600RR
Surgeon General's Warning: It's OK to Smoke V8's
Trey
Site Admin
Posts: 1004
Joined: September 10th, 2002, 11:43 pm
Location: TN
Contact:

Post by Trey »

Done that. Lost 5 whp
pUrExTc
ITRCA Member
Posts: 294
Joined: October 7th, 2002, 5:04 pm
Location: Cerritos, CA
Contact:

Post by pUrExTc »

You got this dyno'ed at AEM in Hawthorne? I think JUN is cheaper...but you have to set up an appointment. Do you have to do that with AEM as well?
'98 Acura Integra Type-R
'03 Honda CBR600RR
Surgeon General's Warning: It's OK to Smoke V8's
Trey
Site Admin
Posts: 1004
Joined: September 10th, 2002, 11:43 pm
Location: TN
Contact:

Post by Trey »

Dyno'd at the Performance Garage in Nashville, TN
pUrExTc
ITRCA Member
Posts: 294
Joined: October 7th, 2002, 5:04 pm
Location: Cerritos, CA
Contact:

Post by pUrExTc »

Isn't it stock the Type-R (USDM) is 195 HP*, and due to the Exhaust Manifold in the JDM Type-R, the JDM one comes out at 197 HP*?

*To the flywheel.
'98 Acura Integra Type-R
'03 Honda CBR600RR
Surgeon General's Warning: It's OK to Smoke V8's
Trey
Site Admin
Posts: 1004
Joined: September 10th, 2002, 11:43 pm
Location: TN
Contact:

Post by Trey »

that is approximately right. Best we know. JDM also has higher compression.
2ktypeR
New ITRCA Member
Posts: 1
Joined: November 7th, 2002, 10:59 pm
Location: 1635 N.Dale Mabry Hwy. Suite 9
Contact:

My dyno run

Post by 2ktypeR »

I have a 2000 R
I have an:

Iceman Cold air intake
Apex- N1 Exhaust
AEM underdrive pulley
test pipe
shaved head
JUN cam gears

Dyno RUN: 181.6 whp
127.6 torque

13.3@99 et

P.S. If you are ever in Tampa and you want to run R to R...let me know.
You better hurry. I plan on getting some Toda spec B's for X-mas
Yes, I will be in the 12's with my full interior all motor R baby!
So many times doors shut behind us that when another one opens in front of us , we dont see it.
Trey
Site Admin
Posts: 1004
Joined: September 10th, 2002, 11:43 pm
Location: TN
Contact:

Re: My dyno run

Post by Trey »

2ktypeR wrote:I have a 2000 R
I have an:

Iceman Cold air intake
Apex- N1 Exhaust
AEM underdrive pulley
test pipe
shaved head
JUN cam gears

Dyno RUN: 181.6 whp
127.6 torque

13.3@99 et

P.S. If you are ever in Tampa and you want to run R to R...let me know.
You better hurry. I plan on getting some Toda spec B's for X-mas
Yes, I will be in the 12's with my full interior all motor R baby!
What sort of weight savings have you done and was that on slicks? Your MPH is kinda low for street tires. What was your 60' time.

No header?
Erik B
Senior ITRCA Member
Posts: 1029
Joined: September 18th, 2002, 12:29 am
Location: Cheyenne, WY
Contact:

Post by Erik B »

13.3??????? :shock:

That track I think is a lil short. I put down 194.3whp and 13lbs of torque and ran a 14.1@99mph on street tires, with a 2.2 60ft and a 9.3 1/8 mile

my mods are as follows:
Toda B's
Toda cams
Toda springs
Spoon header
Spoon head gasket
(GSR) AEM CAI
Test pipe
APEXI VAFC
B&M Fuel Presure reg.
that's what I had when I dyno'ed it. Since then I've added:
(TypeR) AEM CAI
AEM fuel rail
Tanabe exhaust
NITO 555 drag radials
The cars weight was 26??lbs with me in it. The temp was about 80 here in Louisiana with humi at about 90%. I don't know about that 13.3 man.....
2000 Turbo Integra Type R - 508whp/362lbs tq @ 21psi
2003 Imola/Imola NSX-T
http://www.jdmwhoreinc.com
pUrExTc
ITRCA Member
Posts: 294
Joined: October 7th, 2002, 5:04 pm
Location: Cerritos, CA
Contact:

Post by pUrExTc »

what does a stock type-r make down the 1/4 mile anyway?
'98 Acura Integra Type-R
'03 Honda CBR600RR
Surgeon General's Warning: It's OK to Smoke V8's
Trey
Site Admin
Posts: 1004
Joined: September 10th, 2002, 11:43 pm
Location: TN
Contact:

Post by Trey »

14.7 is a good average. Some as fast as 14.4 and as slow as 15.2.
Erik B
Senior ITRCA Member
Posts: 1029
Joined: September 18th, 2002, 12:29 am
Location: Cheyenne, WY
Contact:

Post by Erik B »

14.9 was my best stock
2000 Turbo Integra Type R - 508whp/362lbs tq @ 21psi
2003 Imola/Imola NSX-T
http://www.jdmwhoreinc.com
Trey
Site Admin
Posts: 1004
Joined: September 10th, 2002, 11:43 pm
Location: TN
Contact:

Post by Trey »

Erik B wrote:13.3??????? :shock:

That track I think is a lil short. I put down 194.3whp and 13lbs of torque and ran a 14.1@99mph on street tires, with a 2.2 60ft and a 9.3 1/8 mile
My best to date is a 13.8 @ 101 making 179.0 whp.

See my full setup at http://www.b18c5.net
Locked